MTICS

Metal pipes are very flexible, they can be bent by hand or with bending tool. You can not just bend the pipe at sharp angles – in these places and use the connections (fittings). Fittings for plastic pipes – fun is not cheap, but because of the flexibility they need to be tube nemnogo.Dlya interconnect metal pipes are two main ways:-threaded: push-in connection. This method is most simple to make it may even be a layman. Strongly recommend not to hide the joints in this way for deaf finish – for it must be accessed.

Collet compounds are often "cry": nedokrutil, twisting – they will be felt .- crimping press: the connection by means of press fitting. This operation is performed using a special tool (press mites). Installation conditions virtually eliminate the human factor in quality of the connection. Connections with the press are so reliable that you can use them in a hidden gasket. Polypropylene pipes do not bend, so each turn of the tube – is the use of the fitting. Simple fittings for polypropylene are inexpensive, which is not the combined (shift "thread – polymer": American, couplings with internal or external thread, vodorozetki). If we take as an example of a standard layout of water in the apartment, then combined fittings need a lot of that in general, can make even the cost of wiring and polypropylene tubes are connected . zes the significance of this.

by hot solder. It is believed that with the formation of monolithic connection is more reliable than plastic trub.Ne pretend to argue on this point, but statistics show that the polypropylene compounds are often no more reliable than the elementary threaded connections. 2. The use of plastic and polypropylene pipes for water supply and heating. High-quality metal and plastic tubes are suitable for water and for heating sistem.Polipropilenovye pipes are different, so for a particular issue is best viewed specifications selected pipe.

Sometimes it is a thin layer of plaster on the roof, put a patch NZ fabric and paint over when dry. The holes in the roof glued up, imposing zaplVgy that cut from the sheet, thick burlap? Radar tissue. The size of patches depends on the size of the repaired site. Then prepared from the grated iron or lead minium in natural drying oil zhidVkuyu oil paint, and it is well impregnated cut patches, keeping them in the paint for 10-15 minutes. Patches when lowering the paint must be completely dry. After removing the paint from the patch, squeeze them Here surplus imposed on previously painted, carefully smoothing his hands or stiff brush. Particularly careful Smooth edges. After 5 – I 7 days glued patches dry out, and you can start painting.

Paint should be in dry weather. If cleared to painting the roof stood two weeks or more, it obmetayut brush. When painting the roof for the first time the paint needs to be thinner than the staining for posleduyutsie times. Therefore, for the first na 1 kg of paint colors gustoterSchgoy take 0.6-0.7 kg of linseed oil. Liquid paint sticks to the roof luchSchie and penetrates all the pores. For second and subsequent staining for 1 kg of red gustotertoy take 0.4-0.5 kg of linseed oil. For staining 1m2 roof for a time required on average: ocher, 180-200 g, h umii – 70-90 g, minium iron – 35-40 g, copperhead-250-280 For the longest lifetime yavyyaetsya copperhead.

5-7 days after the first color of the roof okrShShivayut second time, then after 8-10 days Irety paint again. Maslyanaya'kraska completely dries up an average of only 10 days. Compliance with the appropriate mode of paint drying improves the quality of color. Current practice for the second time painting in 1-2 days after first does not give the highest quality. Staining technique of the roof is the same as when painting walls and ceilings.

How to insulate a house? The choice of materials for home insulation are concerned residents of the private sector from year to year. Heaters on the market can be divided into four groups: Quilted – glass and various mineralovata manufacturers, including mineral blocks; Leaf – extruded polystyrene, foams, etc. ; Foam – insulation that is sprayed directly on the structure and "grow" to the desired thickness. It is necessary to distinguish between the foam and liquid-based urethane foams. Other. This group includes a rather exotic or seldom-used insulation, such as mats of plant fibers, cellulose foam, kind of plaster. Experience of friends, acquaintances and neighbors shows that cotton and sheet materials have a low life, which is strongly dependent on compliance technology, "sandwich" and competencies of employees, and the imaginary ecology of these materials can cause allergies.

These problems can be eliminated by using as insulation foam insulation manufactured in Canada Aysinin (Icynene ). From other foam insulations Aysinin by the absence of any fumes, and indefinite service life. Here is a brief list of benefits Aysinin. First, the material has a lifetime warranty Aysinin from the manufacturer. Foam is not curtailed, not deformed and does not age during the entire period of operation. Moreover, applied to a wooden or metal framework Aysinin warns the processes of decay and corrosion, thus extending the life of the building.

Secondly, no additional work to prepare the surface, gluing seams, fastening of insulation and installation of hydro-and vapor-barriers. Aysinin foam has excellent adhesion to all surfaces after application forms a seamless lining, does not require any protective films. Third, Aysinin is 100% water-based, which ensures the absence in its composition of such hazardous substances as phosgene, phenol and formaldehyde. Installation of foam Aysinin is the special equipment (portable spray-water reactors). Immediately after the application of the material increases by about 100 times, filling the tiny cavities and cracks, can insulate places inaccessible to any other heaters.

In the finishing works often use such common materials as paper wallpaper. They have become very popular in the last century, when virtually every apartment is decorated with this kind of wallpaper. There is a reason, as paper wall sufficiently safe for human health, they do not emit into the environment of noxious fumes, as is observed in the plastic covering. Paper wall does not require special training for its use to cover their walls may even people far from painting and decorating. But the paper also have wallpapers and negative moments in its use. If you use classic paper wall, then necessarily be faced with the fact that they can not stand humidity. Therefore, they can not be used in those areas where you need to carefully observe the hygiene requirements.

A little later began to produce water-resistant and washable, they can be glued in wet areas, and even washable. But at the same time reduced their environmental quality. Area exceeds the area of wallpaper wallpaper ordinary paper, so their attachment to the use of special adhesives, which often have toxic substances. The modern trend in decorating materials brought a new kind of wallpaper – a glass or glass cloth. How goes the name suggests, these wallpapers made of glass, but glass cloth wallpaper can be considered not only a piece of glass.

Glass fabric produced by interlacing of many thin strands of fiberglass. The positive side of the glass all known, so these same qualities and have a glass cloth wallpaper. Glass is produced by processing of silicon oxide. The result is a material that has high resistance against various acids, oils, alkalis, organic matter and, of course, water. That is why the glass cloth wallpaper are able to withstand wet cleaning, and handling strong detergents, which may in itself contain acids and bases. Glass cloth wallpaper, thanks to its quality, perfectly suited for use in nurseries, hospitals, shops and similar premises where necessary to adhere to rigorous health and safety standards. Glass also has good resistance against mildew and different organisms. Therefore, glass cloth wallpaper well suited for decoration, where there is frequent high humidity (saunas, pools, baths) as well as their structure will not be exposed to moisture. By itself, the glass can not be used in the form of plates, since it can easily be broken. Therefore, glass cloth wallpaper became a godsend for those who want not only to create beautiful decorated the walls of the room, but also tries to cement lasting less than a finishing material, such as drywall.

Many of us have long been thinking about repairing their apartments. This is quite a serious and responsible step on your part, which requires self-assured solutions and tangible capital, which can transform your ideas into a new style to your home. Repair of apartments, currently a very topical issue. Plus there are all new and new design ideas at the expense of repair and decoration of premises that can transform your space live beyond recognition. In addition, modern technology is walking with long strides, and gives us the opportunity kompanirovat design ideas with home audio and video equipment. If you really hit on the idea of repairing your apartment, is to determine the style.

This is a basic and first step. You need to understand exactly what you want to see after the repair. Decided on the style, then you should consider whether you can pull all the nuances and little things that need to be be addressed during the repair. You may need help in solving small problems that will help you to repair the apartment. After all, you do not want to delay repairs, but on the contrary – we want to make it faster and live in the new style, the new comfort. Some people prefer not to delve into the nature of repair, but only from the correct details. It is convenient and comfortable. You emigrated for a week and a week later get into a brand new apartment.

If we thought up to repair the apartment, then do thorough. Change the floor, insulate the walls, add decorative elements and comfort. To make sure your repair just bring you pleasure and joy. After all, it's nice to come home, where everything in the new design style. Do not be afraid to create a unique solution in the process of repairing the apartment. This is your place of residence, which should bring comfort to you in the first place.

And keep in mind that the enamel should be prepared to work very carefully in the right proportions and mixing foundation hardener. That is why trust your bath professionals, which in this case "the dog ate the" still easier and safer. Most companies offering public services to restore bathtubs, enamel is applied by spraying, rather than manually. This method is considered more reliable, although in fairness, we note that this is only partly true. Experts claim that composition for enamelling shall consist of base and curing agent, and aerosol cans with enamel hardener missing! In addition, when using a spray can inept education streaks and uneven spray. Saving way out is to use compressor rather amateurish spray.

So, if you spray technology offers, ask your master, exactly how it will work – using a spray gun or compressor? Only in latter case, the enamel will be reliable. Besides, any self-respecting company will give you a warranty on the work performed. Enamel – the cheapest, but not the only way to restore the old baths. More modern, though expensive way is to install in your old bathtub acrylic liner. Acrylic – a truly unique material. This polymer is durable (serves more than 20 years without losing its pristine form), sealed, withstands high mechanical loads and high temperatures, environmentally safe and easy to clean.

Acrylic liners are made to order, after "taking off measurements" with your old bathtub. The finished product (and its thickness is only 4mm) is simply inserted into an old bathtub, combining the drain holes and glued together with an old bathtub with a special compound. The edges of the acrylic liner tightly sealed and they squeeze the edge of the old baths, so that they become completely invisible. Of course, this filigree only by specialists. And it costs much more expensive than the enamel. But in your bathtub acrylic clothes will look as good as new! In conclusion, we say that whichever of the Restoration of the above methods you choose, any one of them will be easier and cheaper than installing a new bathroom. And if in your own abilities you are not sure, it's better not to risk it and immediately turn to the professionals. Ovchinka dressing